Angle Valve Installation Costs: Practical Factors in 2023

Table of Contents

Angle Valve Installation Costs, Repair, and Maintenance in 2023 – The angle valve may save you a lot of trouble if you have a leak or a malfunctioning appliance. When you turn the valve off, the water flow throughout your home is entirely stopped, allowing you to perform any required repairs before things get out of hand. This valve will rust or break over time and will need to be replaced. If you need to replace yours, keep reading to discover more about the process, cost, and other details.

⇒ View a List of Angle Valves for Sale and Their Suppliers ⇐

Angle Valve Installation Costs

Angle valve installation costs range from $182.10 to $218.17 per valve. The cost of your project will be determined by the size, circumstances, and finish choices you select. There are several Suppliers and Companies on Linquip which can provide you with a lot of angle valves.

Install An Angle Valve: National Average Cost

The average cost of materials to install an angle valve in the United States is $34.77 per valve, with a range of $32.53 to $37.00. The total cost of labor and materials for each valve is $190.92, with prices ranging from $173.71 to $208.13. Your final cost will be determined by your location, work size, circumstances, and finish selections.

Table 1 Cost to Install an Angle Valve

National Avg. Materials Cost per valve	$34.77
National Avg. Cost (labor and materials) for 1 valve	$190.92
National Cost Range (labor and materials) for 1 valve	$173.71 – $208.13

Angle Valve Installation Methods

A stop valve links a building’s water pipes to the water supply line for a toilet or faucet. A straight stop connects to pipes that penetrate the floor, whereas an angle stop connects to pipes that emerge out of a wall. Both types of stop valves allow a plumber or a homeowner to repair a toilet or faucet without shutting down the whole building’s water supply.

An angle valve, also known as a shut-off valve, will serve you well for many years. Many homeowners repair basic failures without replacing the entire valve, such as leaks that occur around the stem after lengthy periods of inactivity.

Angle stops purchased from a local hardware store are often brass or chrome-plated. Some consumers prefer a multi-turn valve, while others prefer the more dependable and contemporary quarter-turn valve.

Angle valves that serve an ice maker have either a 1/4-inch compression-thread discharge port or utilize a 3/8-inch to 1/4-inch reduction fitting; most domestic angle stops have a 3/8-inch compression-thread discharge port. The type of water pipe used in the building determines the type of intake port: copper, PVC, CPVC, iron pipe, or Polybutylene.

A leak might occur in the seal that surrounds the valve stem. Leaks generally arise after opening or shutting an older valve that is rarely used. Tightening the packing nut on an angle stop, which surrounds the valve stem, will occasionally halt the leak. A significantly degraded or weakened seal, on the other hand, will not keep water.

With one wrench, hold the valve body stationary while rotating the packing nut clockwise with the other. Check your local hardware shop for new components before replacing an angle stop. Replacement components are not available for all valves. Always replace older valves that have lost their capacity to seal entirely due to internal valve body deterioration. For more information, read the Linquip blog about angle valves.

Replacing an Angle Stop Valve

If you attempt to change your angle valve yourself, the new item should only cost you roughly $40. However, this is a job that you should probably leave to the specialists. If you opt to employ a plumber, expect to pay around $236 on average.

The labor involved accounts for the majority of the expense. If you attempt to change this component yourself, you’ll need to know what valve style you currently have. In most homes, a right-angle stop valve is used if the main water pipe runs through the wall, while a straight-stop valve is used if the water enters through the floor. Also, figure out what sort of plumbing you have. It might be plastic, copper, or galvanized, which affects the valve selection process.

Table 2 Angle Valve Replacement Cost

Gadget Cost per Valve	$40
Average Cost	$236

Angle stop water valves all have the same basic replacement steps:

Turn off the water supply to the building.
Release the water pressure in the building’s pipes by opening a hose bib.
Under the current angle stop, place a bucket.
If the angle stop is connected to a detachable supply line, use a wrench to grab the current angle stop and a second wrench to grip the 3/8-inch compression nut that holds the supply tube of the faucet or toilet.
Turn the 3/8-inch compression nut counterclockwise until the nut releases while keeping the angle stop fixed.
The supply tube should be removed. Remove the supply line from the faucet or toilet if the supply line and angle stop are a single item.
Using the appropriate tool, remove the present angle stop.
Remove any dirt from the surface of the 1/2-inch water pipe.
Install the replacement angle stop according to the manufacturer’s instructions.
Tighten the supply tube of the faucet or toilet on the angle stop’s discharge port by hand.
Place one wrench on the body of the angle stop and the other on the 3/8-inch compression nut.
Keep the stop stationary while you turn the 3/8-inch nut clockwise.
Turn on the water supply to the building and inspect the valve for leaks.

Considerations Before Replacing Angle Valve

Before you decide to replace an angle valve, there are a few things to consider. First, determine what sort of plumbing you have and what type of valve you’ll require. If you’re not knowledgeable or comfortable with soldering, you could require a plumber’s aid to finish the work. Always check for leaks after installing a new valve to ensure that everything is secure.

When replacing the valve, bring a bucket to capture any residual water that leaks from the pipe after the old valve is removed. To decide which choice is best for you, compare the costs of changing the valve yourself vs hiring a plumber.

Labor Cost

The majority of the expense of installing a new angle valve is labor, as the supplies should cost less than $40. A plumber will cost between $175 and $250 to do the service in addition to the materials. The cost may vary depending on the type of piping and valve you have/need. Prepare to pay more for work if soldering is necessary or removing the old valve takes longer than intended. Because most plumbers charge by the hour, a basic service should cost less than $300.

DIY vs. Hire A Pro

You can try to change the angle valve yourself. This is a reasonably straightforward job if you have a basic understanding of how plumbing works. Older pipes or copper pipes, on the other hand, need special attention and care, so it may take longer. A skilled plumber can locate the appropriate replacement valve and verify that it is properly installed. They may also provide a guarantee on materials and labor, which may be worth the extra money if you’re worried about future leaks. Visit here for more information about replacement methods.